michfood:
[more] Все-таки поборол я свой ADATA SP900 64GB.
Верной оказалась прошивка как я и предполагал 28199 - как в аналогичном втором живом диске.
Сделал вот такой config:
[more]
[more=config]<GENESIS>
<CONFIGURATION_ID>28199</CONFIGURATION_ID>
<FIRMWARE_OVERRIDE_VERSION>.5.0 6b</FIRMWARE_OVERRIDE_VERSION>
<FLASH_TEST>0</FLASH_TEST>
<EXTERNAL_WRITE_PROTECT>0</EXTERNAL_WRITE_PROTECT>
<MODEL_NO>ADATA SP900</MODEL_NO>
<SERIAL_NUMBER>1D4720126848</SERIAL_NUMBER>
<DEVICE_NOMINAL_FORM_FACTOR>3</DEVICE_NOMINAL_FORM_FACTOR>
<CUSTOMER_ID>0</CUSTOMER_ID>
<DIAGNOSTIC_UNLOCK_KEY>00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00</DIAGNOSTIC_UNLOCK_KEY>
<POWER_MANAGEMENT_VERSION>2</POWER_MANAGEMENT_VERSION>
<SECTOR_SIZE>512</SECTOR_SIZE>
<MAX_LBA_COUNT_FOR_512B_SECTORS>0,125045424,125045424</MAX_LBA_COUNT_FOR_512B_SECTORS>
<MAX_LBA_COUNT_FOR_512B_PLUS_DIFF_SECTORS>0,0,0</MAX_LBA_COUNT_FOR_512B_PLUS_DIFF_SECTORS>
<MAX_LBA_COUNT_FOR_520B_SECTORS>0,0,0</MAX_LBA_COUNT_FOR_520B_SECTORS>
<MAX_LBA_COUNT_FOR_524B_SECTORS>0,0,0</MAX_LBA_COUNT_FOR_524B_SECTORS>
<MAX_LBA_COUNT_FOR_528B_SECTORS>0,0,0</MAX_LBA_COUNT_FOR_528B_SECTORS>
<MAX_LBA_COUNT_FOR_4096_SECTORS>0,0,0</MAX_LBA_COUNT_FOR_4096_SECTORS>
<MAX_LBA_COUNT_FOR_4096_PLUS_DIFF_SECTORS>0,0,0</MAX_LBA_COUNT_FOR_4096_PLUS_DIFF_SECTORS>
<ADDITIONAL_CONFIGURATIONS></ADDITIONAL_CONFIGURATIONS>
<POWER_MANAGEMENT_FEATURE_SELECTION>1</POWER_MANAGEMENT_FEATURE_SELECTION>
<HIPM_BEHAVIOR_IN_ACTIVE_STATE>2</HIPM_BEHAVIOR_IN_ACTIVE_STATE>
<HIPM_BEHAVIOR_IN_IDLE_STATE>2</HIPM_BEHAVIOR_IN_IDLE_STATE>
<HIPM_BEHAVIOR_IN_STANDBY_STATE>2</HIPM_BEHAVIOR_IN_STANDBY_STATE>
<HIPM_BEHAVIOR_IN_SLEEP_STATE>2</HIPM_BEHAVIOR_IN_SLEEP_STATE>
<SENSOR_1_DEVICE_ID>2</SENSOR_1_DEVICE_ID>
<SENSOR_1_DEVICE_ADDRESS></SENSOR_1_DEVICE_ADDRESS>
<SENSOR_2_DEVICE_ID>0xFF</SENSOR_2_DEVICE_ID>
<ALWAYS_RESET_HPA_STATE_ON_COMRESET>0</ALWAYS_RESET_HPA_STATE_ON_COMRESET>
<EOL_THRESHOLD_1_PERCENTAGE>0</EOL_THRESHOLD_1_PERCENTAGE>
<EOL_THRESHOLD_2_PERCENTAGE>0</EOL_THRESHOLD_2_PERCENTAGE>
<VENDOR_SPECIFIC_FIRMWARE_PARAMETERS>00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00</VENDOR_SPECIFIC_FIRMWARE_PARAMETERS>
<CUSTOMER_IDENTIFY_MASK></CUSTOMER_IDENTIFY_MASK>
</GENESIS>[/more]
- немного не по дефолту - но настройки брал из инфо о живом диске:
[more]v0.431a
Drive: 0(ATA)
Model: ADATA SP900
Fw : 5.0.6c
Size : 61057 MB
--- SandForce specific ---
Signature : 158-0-28199
Controller : SF-2000
HW Revision : 400026BB (B02CuPd)
Try to unlock the drive (default)...
Drive unlocked (default)!
FW : [CV5ABBF0 ]
FW string : [B:FW_PPRO_DALECREST:FW_PPRO_C_V_5_Release-545010 ]
Config file : [cfg/cfg_MLC_Intel_64Gb_JS29F16B08CCMF3_1Q_2C_1D_S ]
ROM Revision: [300 ]
NAND ID : 0x89, 0x88, 0x24, 0x4b, 0xa9, 0x84, 0x0, 0x0
Page Size : 8936
NAND CE : 2
Sector/Page : 8
Die/CE : 1
Block/Die : 2048
Page/Block : 256
Raw Size : 134217728
NAND Max EC : 3000
Max PE Cycles : need fw.360+/520+
Cur PE Cycles : need fw.360+/520+
Life In Seconds : 0 (Not Set)
LBA Size : 125045424
Sector Size : 512
Sector Align : +0
NAND ID : 0x89,0x88
Serial Output Control : Default(Off)
Erase R Block : Disable
Panic Handling Enabled : Disable
Panic On SATA Error : Disable
Write Throttling Test Mode: Disable
R.A.I.S.E. : Disable
Flash CE : 8
Bank00: 0x89,0x88,0x24,0x4b,0xa9,0x84,0x0,0x0 - Intel 20nm(L84A) MLC 64Gb/CE 64Gb/die
Bank01: 0x89,0x88,0x24,0x4b,0xa9,0x84,0x0,0x0 - Intel 20nm(L84A) MLC 64Gb/CE 64Gb/die
Bank02: 0x89,0x88,0x24,0x4b,0xa9,0x84,0x0,0x0 - Intel 20nm(L84A) MLC 64Gb/CE 64Gb/die
Bank03: 0x89,0x88,0x24,0x4b,0xa9,0x84,0x0,0x0 - Intel 20nm(L84A) MLC 64Gb/CE 64Gb/die
Bank04: 0x89,0x88,0x24,0x4b,0xa9,0x84,0x0,0x0 - Intel 20nm(L84A) MLC 64Gb/CE 64Gb/die
Bank05: 0x89,0x88,0x24,0x4b,0xa9,0x84,0x0,0x0 - Intel 20nm(L84A) MLC 64Gb/CE 64Gb/die
Bank06: 0x89,0x88,0x24,0x4b,0xa9,0x84,0x0,0x0 - Intel 20nm(L84A) MLC 64Gb/CE 64Gb/die
Bank07: 0x89,0x88,0x24,0x4b,0xa9,0x84,0x0,0x0 - Intel 20nm(L84A) MLC 64Gb/CE 64Gb/die
UART freq : 0
SATA Status Coalescing : 0
Compressible data performance tuning option : 0 (no tuning for compr. data)
Serial Output Control : 0 (Default)
Write Speed Limit : 0 (Off)
Led Settings
Activity LED Polarity : 0 (Normal)
Fault LED Polarity : 0 (Normal)
LED Blink Rate : 0 (250ms)
Power Managment Settings
Power Management Version : 2 (B01)
Active State Power Mode : 0 (Default)
DIPM Behavior in Active State : 0 (Default)
HIPM Behavior in Active State : 2 (HIPM NAK)
Auto Idle Enable : 0 (Default)
Idle State Power Mode : 0 (Default)
DIPM Behavior in Idle State : 0 (Default)
HIPM Behavior in Idle State : 2 (HIPM NAK)
Standby State Power Mode : 0 (Default)
DIPM Behavior in Standby State : 0 (Default)
HIPM Behavior in Standby State : 2 (HIPM NAK)
Sleep State Power Mode : 0 (Default)
DIPM Behavior in Sleep State : 0 (Default)
HIPM Behavior in Sleep State : 2 (HIPM NAK)
Auto slumber timer : 0
CMU power down : 0 (Default)
Dual-align BIST Feature : 0 (Default)
Temperature Sensor Settings
Sensor 1:
Device ID : 2 (LM73)
Device Address : 0
Max Temperature Threshold Level 1 Entry Point (MT1) : 0n (Default - 65C)
Max Temperature Threshold Level 2 Entry Point (MT2) : 0n (Default - 70C)
Min Temperature Threshold (LT1) : 0n (Default - 0C)
Max Temperature Threshold Behavior for MT1 (MT1B) : 0 (Default)
Max Temperature Threshold Behavior for MT2 (MT2B) : 0 (Default)
Min Temperature Threshold Behavior (LT1B) : 0 (Default)
Max Temperature Threshold Level 1 Return Point (MTR1): 0 (Default - MT1)
Sensor 2:
Device ID : 255 (Disabled)
Device Address : 0
Max Temperature Threshold Level 1 Entry Point (MT1) : 0
Max Temperature Threshold Level 2 Entry Point (MT2) : 0
Min Temperature Threshold (LT1) : 0
Max Temperature Threshold Behavior for MT1 (MT1B) : 0 (Default)
Max Temperature Threshold Behavior for MT2 (MT2B) : 0 (Default)
Min Temperature Threshold Behavior (LT1B) : 0 (Default)
Max Temperature Threshold Level 1 Return Point (MTR1): 0
Security Erase Options
Security Erase Behavior : 0 (Default)
Enhanced Security Erase Behavior (Military Erase) : 0 (Default)
SATA Command and Firmware Options
Flush Cache Behavior : 0 (Default)
ATA Security Set Enable : 0 (Default)
Spread Spectrum Clocking Enable : 0 (Default)
SATA Link Handling on Reboot : 0 (Default)
ACS2 Support : 0 (Default)
Failed Secure Unlock Delay Enable : 0 (Default(No delay))
Seek Complete in Error Status : 0 (Default)
Read Long with Retry and without Retry : 0 (Default)
Read Sectors without Retry : 0 (Default)
Write DMA without Retry : 0 (Default)
Write Long with Retry and without Retry : 0 (Default)
Max SATA Link Rate : 0 (Default)
Deterministic Trim Setting : 0 (Default)
Controller Drive Strength Rate : 0 (Default)
PHY Setting : 0 (Default)
Controller Slew Rate : 0 (Default)
Put SIG FIS Delay : 0 (Default)
Set Multiple Handling : 0 (Default)
TRIM Timer Abort : 0 (Enable(Default))
Trim Support/Setting Word 169 Bit 0 : 0 (Default(Firmware default setting))
RDD1 Optimization : 0 (Default)
Security Unlock Drive : 0 (Default(Compare Master Password))
Power Throttling Options
Average Power Level 0-100 : 0
Maximum Power Level 0-100 : 0
Power Throttling Upon Unsafe Shutdown : 0 (Default)
Dynamic Read Scrub
Read Scrub Enabled : 0 (Default (Enabled))
Dynamic Read Scrub End Range1 : 0
Dynamic Read Scrub Rate Range1 : 0
Dynamic Read Scrub End Range2 : 0
Dynamic Read Scrub Rate Range2 : 0
Dynamic Read Scrub End Range3 : 0
Dynamic Read Scrub Rate Range3 : 0
Dynamic Read Scrub End Range4 : 0
Dynamic Read Scrub Rate Range4 : 0
Low Level Format Settings
Number of entries in Max LBA Setting : 1
Sub-Sector Size [0] : 512
Pattern Size [0] : 2
Sub-Sector and Patterns per sector [0] : 0
Max LBA Count [0] : 125045424
Host Protected Area
Host Protected Access : 0 (Always Reset HPA State On COMRESET)
End of Life Behavior
Enable End of Life : 0 (Default (EOL Enabled))
EOL Threshold 1 Type : 0 (Default (SSD Life Left))
EOL Threshold 1 Percentage : 0
EOL Threshold 1 Behavior : 0 (Default (Light Write Throttling))
EOL Threshold 2 Type : 0 (Default (SSD Life Left))
EOL Threshold 1 Percentage : 0
EOL Threshold 1 Behavior : 0 (Default (Heavy Write Throttling))
CDU Smart settings: default
Fab Defect list entry : 11
Idx Bus CE Die Plane Block Lane3210 Defects
0 0 0 0 0 45 BBBB 4
1 0 0 0 1 45 BBBB 4
2 0 1 0 0 45 BBBB 4
3 0 1 0 1 45 BBBB 4
4 0 1 0 0 56 ___B 1
5 0 1 0 0 79 _B__ 1
6 0 1 0 0 128 _B__ 1
7 0 1 0 0 344 ___B 1
8 0 0 0 0 348 ___B 1
9 0 1 0 0 1405 B___ 1
10 0 1 0 0 2027 ___B 1
Fab Defects : 23
User Defect list entry: 0
Panic Dumps : 0
Panic Dumps list:
Idx Accurev SyncCode UnlockLevel Size DataSize EPA Log Ok CRC Ok
0 -1 0xffffffff 0xffffffff -1 -1 0x00040002 0x0000 0x0000
1 -1 0xffffffff 0xffffffff -1 -1 0x00040082 0x0000 0x0000
2 -1 0xffffffff 0xffffffff -1 -1 0x00050002 0x0000 0x0000
3 -1 0xffffffff 0xffffffff -1 -1 0x00050082 0x0000 0x0000
MST settings not exist.
MST result not exits.
[/more]
в оживленном получилось так:
[more]v0.431a
Drive: 3(ATA)
Model: ADATA SP900
Fw : 5.0.6c
Size : 61057 MB
--- SandForce specific ---
Signature : 196-0-28199
Controller : SF-2000
HW Revision : 400026BB (B02CuPd)
FW : [582ABBF0 ]
FW string : [B:FW_PPRO_5_6_1_20140326_836378:FW_PPRO_5_8_2_Release-906190 ]
Config file : [cfg/cfg_MLC_Intel_64Gb_JS29F16B08CCMF3_1Q_2C_1D_S ]
ROM Revision: [300 ]
NAND ID : 0x89, 0x88, 0x24, 0x4b, 0xa9, 0x84, 0x0, 0x0
Page Size : 8936
NAND CE : 2
Sector/Page : 8
Die/CE : 1
Block/Die : 2048
Page/Block : 256
Raw Size : 134217728
NAND Max EC : 3000
Max PE Cycles : 3000
Cur PE Cycles : 0
Life In Seconds : 0 (Not Set)
LBA Size : 125045424
Sector Size : 512
Sector Align : +0
NAND ID : 0x89,0x88
Serial Output Control : Default(Off)
Erase R Block : Disable
Panic Handling Enabled : Disable
Panic On SATA Error : Disable
Write Throttling Test Mode: Disable
R.A.I.S.E. : Disable
Flash CE : 8
Bank00: 0x89,0x88,0x24,0x4b,0xa9,0x84,0x0,0x0 - Intel 20nm(L84A) MLC 64Gb/CE 64Gb/die
Bank01: 0x89,0x88,0x24,0x4b,0xa9,0x84,0x0,0x0 - Intel 20nm(L84A) MLC 64Gb/CE 64Gb/die
Bank02: 0x89,0x88,0x24,0x4b,0xa9,0x84,0x0,0x0 - Intel 20nm(L84A) MLC 64Gb/CE 64Gb/die
Bank03: 0x89,0x88,0x24,0x4b,0xa9,0x84,0x0,0x0 - Intel 20nm(L84A) MLC 64Gb/CE 64Gb/die
Bank04: 0x89,0x88,0x24,0x4b,0xa9,0x84,0x0,0x0 - Intel 20nm(L84A) MLC 64Gb/CE 64Gb/die
Bank05: 0x89,0x88,0x24,0x4b,0xa9,0x84,0x0,0x0 - Intel 20nm(L84A) MLC 64Gb/CE 64Gb/die
Bank06: 0x89,0x88,0x24,0x4b,0xa9,0x84,0x0,0x0 - Intel 20nm(L84A) MLC 64Gb/CE 64Gb/die
Bank07: 0x89,0x88,0x24,0x4b,0xa9,0x84,0x0,0x0 - Intel 20nm(L84A) MLC 64Gb/CE 64Gb/die
UART freq : 0
SATA Status Coalescing : 0
Compressible data performance tuning option : 0 (no tuning for compr. data)
Serial Output Control : 0 (Default)
Write Speed Limit : 0 (Off)
Led Settings
Activity LED Polarity : 0 (Normal)
Fault LED Polarity : 0 (Normal)
LED Blink Rate : 0 (250ms)
Power Managment Settings
Power Management Version : 2 (B01)
Active State Power Mode : 0 (Default)
DIPM Behavior in Active State : 0 (Default)
HIPM Behavior in Active State : 2 (HIPM NAK)
Auto Idle Enable : 0 (Default)
Idle State Power Mode : 0 (Default)
DIPM Behavior in Idle State : 0 (Default)
HIPM Behavior in Idle State : 2 (HIPM NAK)
Standby State Power Mode : 0 (Default)
DIPM Behavior in Standby State : 0 (Default)
HIPM Behavior in Standby State : 2 (HIPM NAK)
Sleep State Power Mode : 0 (Default)
DIPM Behavior in Sleep State : 0 (Default)
HIPM Behavior in Sleep State : 2 (HIPM NAK)
Auto slumber timer : 0
CMU power down : 0 (Default)
Dual-align BIST Feature : 0 (Default)
Temperature Sensor Settings
Sensor 1:
Device ID : 2 (LM73)
Device Address : 0
Max Temperature Threshold Level 1 Entry Point (MT1) : 0n (Default - 65C)
Max Temperature Threshold Level 2 Entry Point (MT2) : 0n (Default - 70C)
Min Temperature Threshold (LT1) : 0n (Default - 0C)
Max Temperature Threshold Behavior for MT1 (MT1B) : 0 (Default)
Max Temperature Threshold Behavior for MT2 (MT2B) : 0 (Default)
Min Temperature Threshold Behavior (LT1B) : 0 (Default)
Max Temperature Threshold Level 1 Return Point (MTR1): 0 (Default - MT1)
Sensor 2:
Device ID : 255 (Disabled)
Device Address : 0
Max Temperature Threshold Level 1 Entry Point (MT1) : 0
Max Temperature Threshold Level 2 Entry Point (MT2) : 0
Min Temperature Threshold (LT1) : 0
Max Temperature Threshold Behavior for MT1 (MT1B) : 0 (Default)
Max Temperature Threshold Behavior for MT2 (MT2B) : 0 (Default)
Min Temperature Threshold Behavior (LT1B) : 0 (Default)
Max Temperature Threshold Level 1 Return Point (MTR1): 0
Security Erase Options
Security Erase Behavior : 0 (Default)
Enhanced Security Erase Behavior (Military Erase) : 0 (Default)
SATA Command and Firmware Options
Flush Cache Behavior : 0 (Default)
ATA Security Set Enable : 0 (Default)
Spread Spectrum Clocking Enable : 0 (Default)
SATA Link Handling on Reboot : 0 (Default)
ACS2 Support : 0 (Default)
Failed Secure Unlock Delay Enable : 0 (Default(No delay))
Seek Complete in Error Status : 0 (Default)
Read Long with Retry and without Retry : 0 (Default)
Read Sectors without Retry : 0 (Default)
Write DMA without Retry : 0 (Default)
Write Long with Retry and without Retry : 0 (Default)
Max SATA Link Rate : 0 (Default)
Deterministic Trim Setting : 0 (Default)
Controller Drive Strength Rate : 0 (Default)
PHY Setting : 0 (Default)
Controller Slew Rate : 0 (Default)
Put SIG FIS Delay : 0 (Default)
Set Multiple Handling : 0 (Default)
TRIM Timer Abort : 0 (Enable(Default))
Trim Support/Setting Word 169 Bit 0 : 0 (Default(Firmware default setting))
RDD1 Optimization : 0 (Default)
Security Unlock Drive : 0 (Default(Compare Master Password))
Power Throttling Options
Average Power Level 0-100 : 0
Maximum Power Level 0-100 : 0
Power Throttling Upon Unsafe Shutdown : 0 (Default)
Dynamic Read Scrub
Read Scrub Enabled : 0 (Default (Enabled))
Dynamic Read Scrub End Range1 : 0
Dynamic Read Scrub Rate Range1 : 0
Dynamic Read Scrub End Range2 : 0
Dynamic Read Scrub Rate Range2 : 0
Dynamic Read Scrub End Range3 : 0
Dynamic Read Scrub Rate Range3 : 0
Dynamic Read Scrub End Range4 : 0
Dynamic Read Scrub Rate Range4 : 0
Low Level Format Settings
Number of entries in Max LBA Setting : 1
Sub-Sector Size [0] : 512
Pattern Size [0] : 2
Sub-Sector and Patterns per sector [0] : 0
Max LBA Count [0] : 125045424
Host Protected Area
Host Protected Access : 1 (Reset only if SSP is disabled)
End of Life Behavior
Enable End of Life : 0 (Default (EOL Enabled))
EOL Threshold 1 Type : 0 (Default (SSD Life Left))
EOL Threshold 1 Percentage : 0
EOL Threshold 1 Behavior : 0 (Default (Light Write Throttling))
EOL Threshold 2 Type : 0 (Default (SSD Life Left))
EOL Threshold 1 Percentage : 0
EOL Threshold 1 Behavior : 0 (Default (Heavy Write Throttling))
CDU Smart settings: default
Fab Defect list entry : 7
Idx Bus CE Die Plane Block Lane3210 Defects
0 0 0 0 0 45 BBBB 4
1 0 0 0 1 45 BBBB 4
2 0 1 0 0 45 BBBB 4
3 0 1 0 1 45 BBBB 4
4 0 1 0 0 128 ___B 1
5 0 1 0 0 557 __B_ 1
6 0 1 0 0 561 __B_ 1
Fab Defects : 19
User Defect list entry: 0
Panic Dumps : 0
Panic Dumps list:
Idx Accurev SyncCode UnlockLevel Size DataSize EPA Log Ok CRC Ok
0 -1 0xffffffff 0xffffffff -1 -1 0x00040002 0x0000 0x0000
1 -1 0xffffffff 0xffffffff -1 -1 0x00040082 0x0000 0x0000
2 -1 0xffffffff 0xffffffff -1 -1 0x00050002 0x0000 0x0000
3 -1 0xffffffff 0xffffffff -1 -1 0x00050082 0x0000 0x0000
MST settings not exist.
MST result not exits.
[/more]
лог FAIL:
[more]ser@localhost ~]$ su
[root@localhost liveuser]# /media/DATA/ADATA/SF_Genesis_v1.7/SF_Genesis -PROCESS_SSD 4:0:0:0 /media/DATA/NEWFL/FW_PPRO_5_8_2_Release.906190.release--0/FW_PPRO_5_8_2_Release.906190.release.0.mfp /media/DATA/NEWFL/FW_PPRO_5_8_2_Release.906190.release--0/Configuration_Files/28199.0.driveconfig 1D4720126848 www_123 log=/media/DATA/ADATA/log
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
SandForce Genesis Utility v1.7.0.01020130612-fc14-32bit
SF_Core Library: v1.7.1.20130612-fc14-32bit
Copyright 2010-2012, LSI Corporation, All Rights Reserved Worldwide.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[Thu 11/28/2019 07:15:32] - SF_Genesis has been invoked with the following parameters:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
argv[1]: -PROCESS_SSD
argv[2]: 4:0:0:0
argv[3]: /media/DATA/NEWFL/FW_PPRO_5_8_2_Release.906190.release--0/FW_PPRO_5_8_2_Release.906190.release.0.mfp
argv[4]: /media/DATA/NEWFL/FW_PPRO_5_8_2_Release.906190.release--0/Configuration_Files/28199.0.driveconfig
argv[5]: 1D4720126848
argv[6]: www_123
argv[7]: log=/media/DATA/ADATA/log
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[Thu 11/28/2019 07:15:32] - Instructing the operating system to purge any existing cached data for device: '4:0:0:0'
[Thu 11/28/2019 07:15:37] - Issuing a discovery command for device: '4:0:0:0'
[Thu 11/28/2019 07:15:42] - Discovery command completed...
[Thu 11/28/2019 07:15:42] - Waiting 5 seconds for the system to settle...
[Thu 11/28/2019 07:15:47] - Device designation string '4:0:0:0' is mapped to node '/dev/sg3'
[Thu 11/28/2019 07:15:47] - Proceeding to process SSD device with the following parameters:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
DeviceName = /dev/sg3
MFP Package Filename = /media/DATA/NEWFL/FW_PPRO_5_8_2_Release.906190.release--0/FW_PPRO_5_8_2_Release.906190.release.0.mfp
Configuration File = /media/DATA/NEWFL/FW_PPRO_5_8_2_Release.906190.release--0/Configuration_Files/28199.0.driveconfig
Serial No. = 1D4720126848
World Wide Name = www_123
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[Thu 11/28/2019 07:15:47] - Successfully received the IDENTIFY data from the drive...
[Thu 11/28/2019 07:15:47] - Validating Manufacturing Firmware Package: /media/DATA/NEWFL/FW_PPRO_5_8_2_Release.906190.release--0/FW_PPRO_5_8_2_Release.906190.release.0.mfp
[Thu 11/28/2019 07:16:36] - Successfully opened the package: /media/DATA/NEWFL/FW_PPRO_5_8_2_Release.906190.release--0/FW_PPRO_5_8_2_Release.906190.release.0.mfp
[Thu 11/28/2019 07:16:36] - file /media/DATA/NEWFL/FW_PPRO_5_8_2_Release.906190.release--0/Configuration_Files/28199.0.driveconfig Loaded successfully
[Thu 11/28/2019 07:16:36] - Warning: Unable to query diagnostics information to perform power management settings check
[Thu 11/28/2019 07:16:36] - B01 Power Management configuration request detected
[Thu 11/28/2019 07:16:36] - Successfully extracted *.DriveConfig file: /media/DATA/NEWFL/FW_PPRO_5_8_2_Release.906190.release--0/Configuration_Files/28199.0.driveconfig
[Thu 11/28/2019 07:16:36] - Extracted Config_ID: 1 (28199) in DriveConfig file: /media/DATA/NEWFL/FW_PPRO_5_8_2_Release.906190.release--0/Configuration_Files/28199.0.driveconfig
[Thu 11/28/2019 07:16:36] - Extracted SerialOutputControl: 0
[Thu 11/28/2019 07:16:57] - Searching for flashware image for configuration 28199
[Thu 11/28/2019 07:16:57] - Manifest found for configuration 28199
[Thu 11/28/2019 07:16:57] - Flashware image extracted: 28199_fw_cl_mlc_Intel_64Gb_JS29F16B08CCMF3_1Q_2C_1D_S_PP_R01909_s512.vic
[Thu 11/28/2019 07:16:57] - Searching for manufacturing image for configuration 28199
[Thu 11/28/2019 07:16:57] - Manifest found for configuration 28199
[Thu 11/28/2019 07:16:57] - Manufacturing image extracted: 28199_mf_mlc_Intel_64Gb_JS29F16B08CCMF3_1Q_2C_1D_S_PP_R01909_s512.vic
[Thu 11/28/2019 07:16:57] - Proceeding in ROM mode, download feature 3...
[Thu 11/28/2019 07:16:57] - Successfully downloaded MFB to the drive...
[Thu 11/28/2019 07:16:57] - Waiting (5 sec) for the drive to settle...
[Thu 11/28/2019 07:17:02] - Successfully received the IDENTIFY data from the drive...
[Thu 11/28/2019 07:17:02] - Firmware revision reported to be: '582ABBM0'. This indicates MFB download was successful.
[Thu 11/28/2019 07:17:02] - Successfully enabled SMART capabilities...
[Thu 11/28/2019 07:17:04] - Successfully issued a diagnostic unlock...
[Thu 11/28/2019 07:17:05] - Performing the flash test of block 0 (0x0000)...
[Thu 11/28/2019 07:17:08] - Flash Test Results:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-----------------------------------------------------------------------------
Flash Test Parameters:
-----------------------------------------------------------------------------
Block Count: 0
Page Count: 1
Bus Count: 1
Chip Enabled Count: 2
Die Count: 1
Lane Count: 4
Plane Count: 2
-----------------------------------------------------------------------------
Results Notes:
-----------------------
N1 - At least one page tested and passed with no bit errors.
N2 - No test data available. Test may have aborted, or failed during the testing.
N3 - At least one page tested and had errors less than or equal to half the range of ECC correction power.
N4 - At least one erased page tested had bit error rate greater than half the correction power.
N5 - Walking zeros test failed.
N6 - Walking ones test failed.
N7 - Block contained factory bad block markings and testing was skipped.
N8 - At least one page tested and had bit error rate greater than the correction power on plane 0.
N9 - Block in plane 0 was marked as a factory bad block.
N10 - At least one page tested and had bit error rate greater than the correction power on plane 1.
N11 - Block in plane 1 was marked as a factory bad block.
-----------------------------------------------------------------------------
+------+------+------+------+--------+--------------------------------------------+---------+
| Bus | CE | Die | Lane | Value | Result Notes | Overall |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 0 | 0 | 0 | 0x0003 | N1,N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 0 | 0 | 1 | 0x0001 | N1 | PASS |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 0 | 0 | 2 | 0x0001 | N1 | PASS |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 0 | 0 | 3 | 0x0001 | N1 | PASS |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 1 | 0 | 0 | 0x0001 | N1 | PASS |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 1 | 0 | 1 | 0x0023 | N1,N3,N5 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 1 | 0 | 2 | 0x0001 | N1 | PASS |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 1 | 0 | 3 | 0x0001 | N1 | PASS |
+------+------+------+------+--------+--------------------------------------------+---------+
-----------------------------------------------------------------------------
Total Number of test results: 8
Number of failures: 0
Number of Passed with warnings: 2
No. Passed without warnings: 6
-----------------------------------------------------------------------------
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[Thu 11/28/2019 07:17:08] - Performing the FORMAT Command with the following parameters:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
MemoryWearCycleCapability = 0
CurrentPE_CycleCount = 0
LifeInSeconds = 0
LogicalCapacity = 125045424
SectorSize = 512
SectorAlignmentOffset = 0
ExpectedMemoryID = 34953 (0x8889)
ExpectedNumDies = 0
SerialOutputControl = 0
Time[8] = 0x0000000000000000
MiscFlag_Erase_R_Block = 0
MiscFlag_PanicHandlingEnabled = 0
MiscFlag_PanicOnSATA_Error = 0
MiscFlag_WriteThrottlingTestMode = 0
MiscFlag_DisableUserBandECCX = 1
L_PageSize = 0
E_PageSize = 0
ErrorCorrectionPower = 0
ConfigDeviceReadDisturbCount = 0
ConfigDeviceReadDisturbCountLow = 0
ExtraOptions_0_1 = 0
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[Thu 11/28/2019 07:17:19] - FATAL_ERROR: Could not perform the FORMAT() operation on the drive... (0x0000C048:SF_SCT (C048h): Root Creation Failed (MFB format))
[Thu 11/28/2019 07:17:19] - End of Genesis manufacturing log.
[Thu 11/28/2019 07:17:19] - Exiting...
[Thu 11/28/2019 07:17:19] - Overall Result for Device: /dev/sg3 ****** FAIL ******
[root@localhost liveuser]# /media/DATA/ADATA/SF_Genesis_v1.7/SF_Genesis -PROCESS_SSD 4:0:0:0 /media/DATA/NEWFL/FW_PPRO_5_8_2_Release.906190.release--0/FW_PPRO_5_8_2_Release.906190.release.0.mfp /media/DATA/NEWFL/FW_PPRO_5_8_2_Release.906190.release--0/Configuration_Files/28199.0.driveconfig 1D4720126848 www_123 log=/media/DATA/ADATA/log
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
SandForce Genesis Utility v1.7.0.01020130612-fc14-32bit
SF_Core Library: v1.7.1.20130612-fc14-32bit
Copyright 2010-2012, LSI Corporation, All Rights Reserved Worldwide.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[Thu 11/28/2019 07:17:53] - SF_Genesis has been invoked with the following parameters:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
argv[1]: -PROCESS_SSD
argv[2]: 4:0:0:0
argv[3]: /media/DATA/NEWFL/FW_PPRO_5_8_2_Release.906190.release--0/FW_PPRO_5_8_2_Release.906190.release.0.mfp
argv[4]: /media/DATA/NEWFL/FW_PPRO_5_8_2_Release.906190.release--0/Configuration_Files/28199.0.driveconfig
argv[5]: 1D4720126848
argv[6]: www_123
argv[7]: log=/media/DATA/ADATA/log
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[Thu 11/28/2019 07:17:53] - Instructing the operating system to purge any existing cached data for device: '4:0:0:0'
[Thu 11/28/2019 07:17:58] - Issuing a discovery command for device: '4:0:0:0'
[Thu 11/28/2019 07:18:03] - Discovery command completed...
[Thu 11/28/2019 07:18:03] - Waiting 5 seconds for the system to settle...
[Thu 11/28/2019 07:18:08] - Device designation string '4:0:0:0' is mapped to node '/dev/sg3'
[Thu 11/28/2019 07:18:08] - Proceeding to process SSD device with the following parameters:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
DeviceName = /dev/sg3
MFP Package Filename = /media/DATA/NEWFL/FW_PPRO_5_8_2_Release.906190.release--0/FW_PPRO_5_8_2_Release.906190.release.0.mfp
Configuration File = /media/DATA/NEWFL/FW_PPRO_5_8_2_Release.906190.release--0/Configuration_Files/28199.0.driveconfig
Serial No. = 1D4720126848
World Wide Name = www_123
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[Thu 11/28/2019 07:18:08] - Successfully received the IDENTIFY data from the drive...
[Thu 11/28/2019 07:18:08] - FATAL_ERROR: This drive is already running MFB, please perform a force-download to enter in to the ROM mode first. Genesis can not process drive in the current state... (0x10090020:SF_GENESIS_ALREADY_RUNNING_MFB_ERROR)
[Thu 11/28/2019 07:18:08] - End of Genesis manufacturing log.
[Thu 11/28/2019 07:18:08] - Exiting...
[Thu 11/28/2019 07:18:08] - Overall Result for Device: /dev/sg3 ****** FAIL ******
[root@localhost liveuser]#
[/more]
лог PASS:
[more]ser@localhost ~]$ su
[root@localhost liveuser]# /media/DATA/ADATA/SF_Genesis_v1.7/SF_Genesis -PROCESS_SSD 4:0:0:0 /media/DATA/NEWFL/FW_PPRO_5_8_2_Release.906190.release--0/FW_PPRO_5_8_2_Release.906190.release.0.mfp /media/DATA/NEWFL/FW_PPRO_5_8_2_Release.906190.release--0/Configuration_Files/28199.0.driveconfig 1D4720126848 www_123 log=/media/DATA/ADATA/log
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
SandForce Genesis Utility v1.7.0.01020130612-fc14-32bit
SF_Core Library: v1.7.1.20130612-fc14-32bit
Copyright 2010-2012, LSI Corporation, All Rights Reserved Worldwide.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[Thu 11/28/2019 19:16:48] - SF_Genesis has been invoked with the following parameters:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
argv[1]: -PROCESS_SSD
argv[2]: 4:0:0:0
argv[3]: /media/DATA/NEWFL/FW_PPRO_5_8_2_Release.906190.release--0/FW_PPRO_5_8_2_Release.906190.release.0.mfp
argv[4]: /media/DATA/NEWFL/FW_PPRO_5_8_2_Release.906190.release--0/Configuration_Files/28199.0.driveconfig
argv[5]: 1D4720126848
argv[6]: www_123
argv[7]: log=/media/DATA/ADATA/log
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[Thu 11/28/2019 19:16:48] - Instructing the operating system to purge any existing cached data for device: '4:0:0:0'
[Thu 11/28/2019 19:16:53] - Issuing a discovery command for device: '4:0:0:0'
[Thu 11/28/2019 19:16:58] - Discovery command completed...
[Thu 11/28/2019 19:16:58] - Waiting 5 seconds for the system to settle...
[Thu 11/28/2019 19:17:03] - Device designation string '4:0:0:0' is mapped to node '/dev/sg3'
[Thu 11/28/2019 19:17:03] - Proceeding to process SSD device with the following parameters:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
DeviceName = /dev/sg3
MFP Package Filename = /media/DATA/NEWFL/FW_PPRO_5_8_2_Release.906190.release--0/FW_PPRO_5_8_2_Release.906190.release.0.mfp
Configuration File = /media/DATA/NEWFL/FW_PPRO_5_8_2_Release.906190.release--0/Configuration_Files/28199.0.driveconfig
Serial No. = 1D4720126848
World Wide Name = www_123
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[Thu 11/28/2019 19:17:03] - Successfully received the IDENTIFY data from the drive...
[Thu 11/28/2019 19:17:03] - Validating Manufacturing Firmware Package: /media/DATA/NEWFL/FW_PPRO_5_8_2_Release.906190.release--0/FW_PPRO_5_8_2_Release.906190.release.0.mfp
[Thu 11/28/2019 19:17:52] - Successfully opened the package: /media/DATA/NEWFL/FW_PPRO_5_8_2_Release.906190.release--0/FW_PPRO_5_8_2_Release.906190.release.0.mfp
[Thu 11/28/2019 19:17:52] - file /media/DATA/NEWFL/FW_PPRO_5_8_2_Release.906190.release--0/Configuration_Files/28199.0.driveconfig Loaded successfully
[Thu 11/28/2019 19:17:52] - Warning: Unable to query diagnostics information to perform power management settings check
[Thu 11/28/2019 19:17:52] - B01 Power Management configuration request detected
[Thu 11/28/2019 19:17:52] - Successfully extracted *.DriveConfig file: /media/DATA/NEWFL/FW_PPRO_5_8_2_Release.906190.release--0/Configuration_Files/28199.0.driveconfig
[Thu 11/28/2019 19:17:52] - Extracted Config_ID: 1 (28199) in DriveConfig file: /media/DATA/NEWFL/FW_PPRO_5_8_2_Release.906190.release--0/Configuration_Files/28199.0.driveconfig
[Thu 11/28/2019 19:17:52] - Extracted SerialOutputControl: 0
[Thu 11/28/2019 19:18:13] - Searching for flashware image for configuration 28199
[Thu 11/28/2019 19:18:13] - Manifest found for configuration 28199
[Thu 11/28/2019 19:18:13] - Flashware image extracted: 28199_fw_cl_mlc_Intel_64Gb_JS29F16B08CCMF3_1Q_2C_1D_S_PP_R01909_s512.vic
[Thu 11/28/2019 19:18:13] - Searching for manufacturing image for configuration 28199
[Thu 11/28/2019 19:18:13] - Manifest found for configuration 28199
[Thu 11/28/2019 19:18:13] - Manufacturing image extracted: 28199_mf_mlc_Intel_64Gb_JS29F16B08CCMF3_1Q_2C_1D_S_PP_R01909_s512.vic
[Thu 11/28/2019 19:18:13] - Proceeding in ROM mode, download feature 3...
[Thu 11/28/2019 19:18:13] - Successfully downloaded MFB to the drive...
[Thu 11/28/2019 19:18:13] - Waiting (5 sec) for the drive to settle...
[Thu 11/28/2019 19:18:18] - Successfully received the IDENTIFY data from the drive...
[Thu 11/28/2019 19:18:18] - Firmware revision reported to be: '582ABBM0'. This indicates MFB download was successful.
[Thu 11/28/2019 19:18:18] - Successfully enabled SMART capabilities...
[Thu 11/28/2019 19:18:20] - Successfully issued a diagnostic unlock...
[Thu 11/28/2019 19:18:21] - Performing the FORMAT Command with the following parameters:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
MemoryWearCycleCapability = 0
CurrentPE_CycleCount = 0
LifeInSeconds = 0
LogicalCapacity = 125045424
SectorSize = 512
SectorAlignmentOffset = 0
ExpectedMemoryID = 34953 (0x8889)
ExpectedNumDies = 0
SerialOutputControl = 0
Time[8] = 0x0000000000000000
MiscFlag_Erase_R_Block = 0
MiscFlag_PanicHandlingEnabled = 0
MiscFlag_PanicOnSATA_Error = 0
MiscFlag_WriteThrottlingTestMode = 0
MiscFlag_DisableUserBandECCX = 1
L_PageSize = 0
E_PageSize = 0
ErrorCorrectionPower = 0
ConfigDeviceReadDisturbCount = 0
ConfigDeviceReadDisturbCountLow = 0
ExtraOptions_0_1 = 0
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[Thu 11/28/2019 19:18:29] - FORMAT command completed...
[Thu 11/28/2019 19:18:29] - Waiting (2 sec) for the drive to settle...
[Thu 11/28/2019 19:18:31] - Setting up the stamp information through CDU command...
[Thu 11/28/2019 19:18:34] - Waiting (2 sec) for the drive to settle...
[Thu 11/28/2019 19:18:36] - Downloading the flashware to the drive... feature 3
[Thu 11/28/2019 19:18:38] - Successfully downloaded flashware to the drive...
[Thu 11/28/2019 19:18:38] - Waiting (15 sec) for the drive to settle...
[Thu 11/28/2019 19:18:53] - Successfully received the IDENTIFY data from the drive...
[Thu 11/28/2019 19:18:53] - Firmware revision reported to be: '4.0.0 '
[Thu 11/28/2019 19:18:53] - Enabling SMART support...
[Thu 11/28/2019 19:18:53] - Issuing a diagnostic unlock to the drive...
[Thu 11/28/2019 19:18:55] - Setting up Max LBA settings...
[Thu 11/28/2019 19:18:59] - Change of sector size is not required, sector size is already set to 512
[Thu 11/28/2019 19:19:00] - Setting the serial number of the drive to: 1D4720126848
[Thu 11/28/2019 19:19:02] - Setting the World Wide Name (WWN) of the drive to: www_123
[Thu 11/28/2019 19:19:05] - Processing completed for device: 1D4720126848
[Thu 11/28/2019 19:19:05] - Begin collecting the device post-process log/information
[Thu 11/28/2019 19:19:05] - Creating the Log Bundle...
[Thu 11/28/2019 19:19:05] - Plain text identify log created
[Thu 11/28/2019 19:19:06] - Plain text diagnostics identify log created
[Thu 11/28/2019 19:19:07] - Plain text diagnostics information log created
[Thu 11/28/2019 19:19:08] - Plain text format information log created
[Thu 11/28/2019 19:19:08] - Plain text SMART log created
[Thu 11/28/2019 19:19:10] - Plain text manufacturing defect list log created
[Thu 11/28/2019 19:19:11] - Plain text grown defect list log created
[Thu 11/28/2019 19:19:12] - Plain text panic directory listing log created
[Thu 11/28/2019 19:19:12] - Completed collecting all plain text log files.
[Thu 11/28/2019 19:19:12] - End of logs and information collection
[Thu 11/28/2019 19:19:13] - Applying the remaining ConfigUniqueDrive settings...
[Thu 11/28/2019 19:19:14] - Setting Customer ID with value : 0
[Thu 11/28/2019 19:19:14] - Setting Diagnostic Unlock Key with value supplied
[Thu 11/28/2019 19:19:14] - Setting Max LBA Count for 4096 Plus DIFF Sectors with value : 0
[Thu 11/28/2019 19:19:14] - Setting Max LBA Count for 4096 Sectors with value : 0
[Thu 11/28/2019 19:19:14] - Setting Max LBA Count for 512B Plus DIFF Sectors with value : 0
[Thu 11/28/2019 19:19:14] - Setting Max LBA Count for 512B Sectors with value : 0
[Thu 11/28/2019 19:19:14] - Setting Max LBA Count for 520B Sectors with value : 0
[Thu 11/28/2019 19:19:14] - Setting Max LBA Count for 524B Sectors with value : 0
[Thu 11/28/2019 19:19:14] - Setting Max LBA Count for 528B Sectors with value : 0
[Thu 11/28/2019 19:19:14] - Total of 1 valid MaxLBA settings were setup to be written to the drive.
[Thu 11/28/2019 19:19:16] - Successfully applied the remaining ConfigUniqueDrive settings...
[Thu 11/28/2019 19:19:16] - Issuing an IdleImmediate command to the drive...
[Thu 11/28/2019 19:19:16] - Not an Enterprise drive,so, continuing without setting master password..
[Thu 11/28/2019 19:19:16] - End of Genesis manufacturing log.
[Thu 11/28/2019 19:19:16] - Exiting...
[Thu 11/28/2019 19:19:16] - Overall Result for Device: /dev/sg3 ****** PASS ******
[root@localhost liveuser]# ^C
[root@localhost liveuser]#
[/more]
Мне кажется, что ошибки при прошивке возникают при включенной галке Test Flash. Тогда Genesis видимо прогонят память на бэды и если ему что-то не нравится - дальше не шьет.
Т.е. если есть такая запись в логе:
[more][Thu 11/28/2019 07:17:08] - Flash Test Results:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-----------------------------------------------------------------------------
Flash Test Parameters:
-----------------------------------------------------------------------------
Block Count: 0
Page Count: 1
Bus Count: 1
Chip Enabled Count: 2
Die Count: 1
Lane Count: 4
Plane Count: 2
-----------------------------------------------------------------------------
Results Notes:
-----------------------
N1 - At least one page tested and passed with no bit errors.
N2 - No test data available. Test may have aborted, or failed during the testing.
N3 - At least one page tested and had errors less than or equal to half the range of ECC correction power.
N4 - At least one erased page tested had bit error rate greater than half the correction power.
N5 - Walking zeros test failed.
N6 - Walking ones test failed.
N7 - Block contained factory bad block markings and testing was skipped.
N8 - At least one page tested and had bit error rate greater than the correction power on plane 0.
N9 - Block in plane 0 was marked as a factory bad block.
N10 - At least one page tested and had bit error rate greater than the correction power on plane 1.
N11 - Block in plane 1 was marked as a factory bad block.
-----------------------------------------------------------------------------
+------+------+------+------+--------+--------------------------------------------+---------+
| Bus | CE | Die | Lane | Value | Result Notes | Overall |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 0 | 0 | 0 | 0x0003 | N1,N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 0 | 0 | 1 | 0x0001 | N1 | PASS |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 0 | 0 | 2 | 0x0001 | N1 | PASS |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 0 | 0 | 3 | 0x0001 | N1 | PASS |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 1 | 0 | 0 | 0x0001 | N1 | PASS |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 1 | 0 | 1 | 0x0023 | N1,N3,N5 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 1 | 0 | 2 | 0x0001 | N1 | PASS |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 1 | 0 | 3 | 0x0001 | N1 | PASS |
+------+------+------+------+--------+--------------------------------------------+---------+[/more]
- скорее всего не прошьется - все что кроме N1 будет приводить к ошибке.
Чтобы программа sp_info могла прочитать данные - Device Unlock Code надо ставить 16 нулей, а не как пишут везде 1,2,3,4,5,6,7,8,9,0,1,2,3,4,5,6. Это можно ручками прямо в конфиге прописать.
Ну и после прошивки имею следющие отличия от второго диска:
Signature : 158-0-28199 - на родном, Signature : 196-0-28199 - на прошитом. Думаю это vendor ID - ни на что не влияет, программа ADATA диск видит.
На непрошитом диске:
FW : [CV5ABBF0 ]
FW string : [B:FW_PPRO_DALECREST:FW_PPRO_C_V_5_Release-545010
На прошитом:
FW : [582ABBF0 ]
FW string : [B:FW_PPRO_5_6_1_20140326_836378:FW_PPRO_5_8_2_Release-906190
- думаю прошивка все-же не такая как была, более новая, но не уверен.
Однако по тестам скорости - она стала выше раза в 1,5 и на чтение и на запись.
Еще в непрошитом:
Max PE Cycles : need fw.360+/520+
Cur PE Cycles : need fw.360+/520+
А в прошитом:
Max PE Cycles : 3000
Cur PE Cycles : 0
что это такое - не знаю, но время жизни показывает как-то по разному.
Всем огромное спасибо за собранный материал и помощь!
Жалко что сам ресурс не очень юзабельный... крайне тяжело работать с таким форумом... но может это дело привычки. [/more] [/more]
[more] Все-таки поборол я свой ADATA SP900 64GB.
Верной оказалась прошивка как я и предполагал 28199 - как в аналогичном втором живом диске.
Сделал вот такой config:
[more]
[more=config]<GENESIS>
<CONFIGURATION_ID>28199</CONFIGURATION_ID>
<FIRMWARE_OVERRIDE_VERSION>.5.0 6b</FIRMWARE_OVERRIDE_VERSION>
<FLASH_TEST>0</FLASH_TEST>
<EXTERNAL_WRITE_PROTECT>0</EXTERNAL_WRITE_PROTECT>
<MODEL_NO>ADATA SP900</MODEL_NO>
<SERIAL_NUMBER>1D4720126848</SERIAL_NUMBER>
<DEVICE_NOMINAL_FORM_FACTOR>3</DEVICE_NOMINAL_FORM_FACTOR>
<CUSTOMER_ID>0</CUSTOMER_ID>
<DIAGNOSTIC_UNLOCK_KEY>00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00</DIAGNOSTIC_UNLOCK_KEY>
<POWER_MANAGEMENT_VERSION>2</POWER_MANAGEMENT_VERSION>
<SECTOR_SIZE>512</SECTOR_SIZE>
<MAX_LBA_COUNT_FOR_512B_SECTORS>0,125045424,125045424</MAX_LBA_COUNT_FOR_512B_SECTORS>
<MAX_LBA_COUNT_FOR_512B_PLUS_DIFF_SECTORS>0,0,0</MAX_LBA_COUNT_FOR_512B_PLUS_DIFF_SECTORS>
<MAX_LBA_COUNT_FOR_520B_SECTORS>0,0,0</MAX_LBA_COUNT_FOR_520B_SECTORS>
<MAX_LBA_COUNT_FOR_524B_SECTORS>0,0,0</MAX_LBA_COUNT_FOR_524B_SECTORS>
<MAX_LBA_COUNT_FOR_528B_SECTORS>0,0,0</MAX_LBA_COUNT_FOR_528B_SECTORS>
<MAX_LBA_COUNT_FOR_4096_SECTORS>0,0,0</MAX_LBA_COUNT_FOR_4096_SECTORS>
<MAX_LBA_COUNT_FOR_4096_PLUS_DIFF_SECTORS>0,0,0</MAX_LBA_COUNT_FOR_4096_PLUS_DIFF_SECTORS>
<ADDITIONAL_CONFIGURATIONS></ADDITIONAL_CONFIGURATIONS>
<POWER_MANAGEMENT_FEATURE_SELECTION>1</POWER_MANAGEMENT_FEATURE_SELECTION>
<HIPM_BEHAVIOR_IN_ACTIVE_STATE>2</HIPM_BEHAVIOR_IN_ACTIVE_STATE>
<HIPM_BEHAVIOR_IN_IDLE_STATE>2</HIPM_BEHAVIOR_IN_IDLE_STATE>
<HIPM_BEHAVIOR_IN_STANDBY_STATE>2</HIPM_BEHAVIOR_IN_STANDBY_STATE>
<HIPM_BEHAVIOR_IN_SLEEP_STATE>2</HIPM_BEHAVIOR_IN_SLEEP_STATE>
<SENSOR_1_DEVICE_ID>2</SENSOR_1_DEVICE_ID>
<SENSOR_1_DEVICE_ADDRESS></SENSOR_1_DEVICE_ADDRESS>
<SENSOR_2_DEVICE_ID>0xFF</SENSOR_2_DEVICE_ID>
<ALWAYS_RESET_HPA_STATE_ON_COMRESET>0</ALWAYS_RESET_HPA_STATE_ON_COMRESET>
<EOL_THRESHOLD_1_PERCENTAGE>0</EOL_THRESHOLD_1_PERCENTAGE>
<EOL_THRESHOLD_2_PERCENTAGE>0</EOL_THRESHOLD_2_PERCENTAGE>
<VENDOR_SPECIFIC_FIRMWARE_PARAMETERS>00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00</VENDOR_SPECIFIC_FIRMWARE_PARAMETERS>
<CUSTOMER_IDENTIFY_MASK></CUSTOMER_IDENTIFY_MASK>
</GENESIS>[/more]
- немного не по дефолту - но настройки брал из инфо о живом диске:
[more]v0.431a
Drive: 0(ATA)
Model: ADATA SP900
Fw : 5.0.6c
Size : 61057 MB
--- SandForce specific ---
Signature : 158-0-28199
Controller : SF-2000
HW Revision : 400026BB (B02CuPd)
Try to unlock the drive (default)...
Drive unlocked (default)!
FW : [CV5ABBF0 ]
FW string : [B:FW_PPRO_DALECREST:FW_PPRO_C_V_5_Release-545010 ]
Config file : [cfg/cfg_MLC_Intel_64Gb_JS29F16B08CCMF3_1Q_2C_1D_S ]
ROM Revision: [300 ]
NAND ID : 0x89, 0x88, 0x24, 0x4b, 0xa9, 0x84, 0x0, 0x0
Page Size : 8936
NAND CE : 2
Sector/Page : 8
Die/CE : 1
Block/Die : 2048
Page/Block : 256
Raw Size : 134217728
NAND Max EC : 3000
Max PE Cycles : need fw.360+/520+
Cur PE Cycles : need fw.360+/520+
Life In Seconds : 0 (Not Set)
LBA Size : 125045424
Sector Size : 512
Sector Align : +0
NAND ID : 0x89,0x88
Serial Output Control : Default(Off)
Erase R Block : Disable
Panic Handling Enabled : Disable
Panic On SATA Error : Disable
Write Throttling Test Mode: Disable
R.A.I.S.E. : Disable
Flash CE : 8
Bank00: 0x89,0x88,0x24,0x4b,0xa9,0x84,0x0,0x0 - Intel 20nm(L84A) MLC 64Gb/CE 64Gb/die
Bank01: 0x89,0x88,0x24,0x4b,0xa9,0x84,0x0,0x0 - Intel 20nm(L84A) MLC 64Gb/CE 64Gb/die
Bank02: 0x89,0x88,0x24,0x4b,0xa9,0x84,0x0,0x0 - Intel 20nm(L84A) MLC 64Gb/CE 64Gb/die
Bank03: 0x89,0x88,0x24,0x4b,0xa9,0x84,0x0,0x0 - Intel 20nm(L84A) MLC 64Gb/CE 64Gb/die
Bank04: 0x89,0x88,0x24,0x4b,0xa9,0x84,0x0,0x0 - Intel 20nm(L84A) MLC 64Gb/CE 64Gb/die
Bank05: 0x89,0x88,0x24,0x4b,0xa9,0x84,0x0,0x0 - Intel 20nm(L84A) MLC 64Gb/CE 64Gb/die
Bank06: 0x89,0x88,0x24,0x4b,0xa9,0x84,0x0,0x0 - Intel 20nm(L84A) MLC 64Gb/CE 64Gb/die
Bank07: 0x89,0x88,0x24,0x4b,0xa9,0x84,0x0,0x0 - Intel 20nm(L84A) MLC 64Gb/CE 64Gb/die
UART freq : 0
SATA Status Coalescing : 0
Compressible data performance tuning option : 0 (no tuning for compr. data)
Serial Output Control : 0 (Default)
Write Speed Limit : 0 (Off)
Led Settings
Activity LED Polarity : 0 (Normal)
Fault LED Polarity : 0 (Normal)
LED Blink Rate : 0 (250ms)
Power Managment Settings
Power Management Version : 2 (B01)
Active State Power Mode : 0 (Default)
DIPM Behavior in Active State : 0 (Default)
HIPM Behavior in Active State : 2 (HIPM NAK)
Auto Idle Enable : 0 (Default)
Idle State Power Mode : 0 (Default)
DIPM Behavior in Idle State : 0 (Default)
HIPM Behavior in Idle State : 2 (HIPM NAK)
Standby State Power Mode : 0 (Default)
DIPM Behavior in Standby State : 0 (Default)
HIPM Behavior in Standby State : 2 (HIPM NAK)
Sleep State Power Mode : 0 (Default)
DIPM Behavior in Sleep State : 0 (Default)
HIPM Behavior in Sleep State : 2 (HIPM NAK)
Auto slumber timer : 0
CMU power down : 0 (Default)
Dual-align BIST Feature : 0 (Default)
Temperature Sensor Settings
Sensor 1:
Device ID : 2 (LM73)
Device Address : 0
Max Temperature Threshold Level 1 Entry Point (MT1) : 0n (Default - 65C)
Max Temperature Threshold Level 2 Entry Point (MT2) : 0n (Default - 70C)
Min Temperature Threshold (LT1) : 0n (Default - 0C)
Max Temperature Threshold Behavior for MT1 (MT1B) : 0 (Default)
Max Temperature Threshold Behavior for MT2 (MT2B) : 0 (Default)
Min Temperature Threshold Behavior (LT1B) : 0 (Default)
Max Temperature Threshold Level 1 Return Point (MTR1): 0 (Default - MT1)
Sensor 2:
Device ID : 255 (Disabled)
Device Address : 0
Max Temperature Threshold Level 1 Entry Point (MT1) : 0
Max Temperature Threshold Level 2 Entry Point (MT2) : 0
Min Temperature Threshold (LT1) : 0
Max Temperature Threshold Behavior for MT1 (MT1B) : 0 (Default)
Max Temperature Threshold Behavior for MT2 (MT2B) : 0 (Default)
Min Temperature Threshold Behavior (LT1B) : 0 (Default)
Max Temperature Threshold Level 1 Return Point (MTR1): 0
Security Erase Options
Security Erase Behavior : 0 (Default)
Enhanced Security Erase Behavior (Military Erase) : 0 (Default)
SATA Command and Firmware Options
Flush Cache Behavior : 0 (Default)
ATA Security Set Enable : 0 (Default)
Spread Spectrum Clocking Enable : 0 (Default)
SATA Link Handling on Reboot : 0 (Default)
ACS2 Support : 0 (Default)
Failed Secure Unlock Delay Enable : 0 (Default(No delay))
Seek Complete in Error Status : 0 (Default)
Read Long with Retry and without Retry : 0 (Default)
Read Sectors without Retry : 0 (Default)
Write DMA without Retry : 0 (Default)
Write Long with Retry and without Retry : 0 (Default)
Max SATA Link Rate : 0 (Default)
Deterministic Trim Setting : 0 (Default)
Controller Drive Strength Rate : 0 (Default)
PHY Setting : 0 (Default)
Controller Slew Rate : 0 (Default)
Put SIG FIS Delay : 0 (Default)
Set Multiple Handling : 0 (Default)
TRIM Timer Abort : 0 (Enable(Default))
Trim Support/Setting Word 169 Bit 0 : 0 (Default(Firmware default setting))
RDD1 Optimization : 0 (Default)
Security Unlock Drive : 0 (Default(Compare Master Password))
Power Throttling Options
Average Power Level 0-100 : 0
Maximum Power Level 0-100 : 0
Power Throttling Upon Unsafe Shutdown : 0 (Default)
Dynamic Read Scrub
Read Scrub Enabled : 0 (Default (Enabled))
Dynamic Read Scrub End Range1 : 0
Dynamic Read Scrub Rate Range1 : 0
Dynamic Read Scrub End Range2 : 0
Dynamic Read Scrub Rate Range2 : 0
Dynamic Read Scrub End Range3 : 0
Dynamic Read Scrub Rate Range3 : 0
Dynamic Read Scrub End Range4 : 0
Dynamic Read Scrub Rate Range4 : 0
Low Level Format Settings
Number of entries in Max LBA Setting : 1
Sub-Sector Size [0] : 512
Pattern Size [0] : 2
Sub-Sector and Patterns per sector [0] : 0
Max LBA Count [0] : 125045424
Host Protected Area
Host Protected Access : 0 (Always Reset HPA State On COMRESET)
End of Life Behavior
Enable End of Life : 0 (Default (EOL Enabled))
EOL Threshold 1 Type : 0 (Default (SSD Life Left))
EOL Threshold 1 Percentage : 0
EOL Threshold 1 Behavior : 0 (Default (Light Write Throttling))
EOL Threshold 2 Type : 0 (Default (SSD Life Left))
EOL Threshold 1 Percentage : 0
EOL Threshold 1 Behavior : 0 (Default (Heavy Write Throttling))
CDU Smart settings: default
Fab Defect list entry : 11
Idx Bus CE Die Plane Block Lane3210 Defects
0 0 0 0 0 45 BBBB 4
1 0 0 0 1 45 BBBB 4
2 0 1 0 0 45 BBBB 4
3 0 1 0 1 45 BBBB 4
4 0 1 0 0 56 ___B 1
5 0 1 0 0 79 _B__ 1
6 0 1 0 0 128 _B__ 1
7 0 1 0 0 344 ___B 1
8 0 0 0 0 348 ___B 1
9 0 1 0 0 1405 B___ 1
10 0 1 0 0 2027 ___B 1
Fab Defects : 23
User Defect list entry: 0
Panic Dumps : 0
Panic Dumps list:
Idx Accurev SyncCode UnlockLevel Size DataSize EPA Log Ok CRC Ok
0 -1 0xffffffff 0xffffffff -1 -1 0x00040002 0x0000 0x0000
1 -1 0xffffffff 0xffffffff -1 -1 0x00040082 0x0000 0x0000
2 -1 0xffffffff 0xffffffff -1 -1 0x00050002 0x0000 0x0000
3 -1 0xffffffff 0xffffffff -1 -1 0x00050082 0x0000 0x0000
MST settings not exist.
MST result not exits.
[/more]
в оживленном получилось так:
[more]v0.431a
Drive: 3(ATA)
Model: ADATA SP900
Fw : 5.0.6c
Size : 61057 MB
--- SandForce specific ---
Signature : 196-0-28199
Controller : SF-2000
HW Revision : 400026BB (B02CuPd)
FW : [582ABBF0 ]
FW string : [B:FW_PPRO_5_6_1_20140326_836378:FW_PPRO_5_8_2_Release-906190 ]
Config file : [cfg/cfg_MLC_Intel_64Gb_JS29F16B08CCMF3_1Q_2C_1D_S ]
ROM Revision: [300 ]
NAND ID : 0x89, 0x88, 0x24, 0x4b, 0xa9, 0x84, 0x0, 0x0
Page Size : 8936
NAND CE : 2
Sector/Page : 8
Die/CE : 1
Block/Die : 2048
Page/Block : 256
Raw Size : 134217728
NAND Max EC : 3000
Max PE Cycles : 3000
Cur PE Cycles : 0
Life In Seconds : 0 (Not Set)
LBA Size : 125045424
Sector Size : 512
Sector Align : +0
NAND ID : 0x89,0x88
Serial Output Control : Default(Off)
Erase R Block : Disable
Panic Handling Enabled : Disable
Panic On SATA Error : Disable
Write Throttling Test Mode: Disable
R.A.I.S.E. : Disable
Flash CE : 8
Bank00: 0x89,0x88,0x24,0x4b,0xa9,0x84,0x0,0x0 - Intel 20nm(L84A) MLC 64Gb/CE 64Gb/die
Bank01: 0x89,0x88,0x24,0x4b,0xa9,0x84,0x0,0x0 - Intel 20nm(L84A) MLC 64Gb/CE 64Gb/die
Bank02: 0x89,0x88,0x24,0x4b,0xa9,0x84,0x0,0x0 - Intel 20nm(L84A) MLC 64Gb/CE 64Gb/die
Bank03: 0x89,0x88,0x24,0x4b,0xa9,0x84,0x0,0x0 - Intel 20nm(L84A) MLC 64Gb/CE 64Gb/die
Bank04: 0x89,0x88,0x24,0x4b,0xa9,0x84,0x0,0x0 - Intel 20nm(L84A) MLC 64Gb/CE 64Gb/die
Bank05: 0x89,0x88,0x24,0x4b,0xa9,0x84,0x0,0x0 - Intel 20nm(L84A) MLC 64Gb/CE 64Gb/die
Bank06: 0x89,0x88,0x24,0x4b,0xa9,0x84,0x0,0x0 - Intel 20nm(L84A) MLC 64Gb/CE 64Gb/die
Bank07: 0x89,0x88,0x24,0x4b,0xa9,0x84,0x0,0x0 - Intel 20nm(L84A) MLC 64Gb/CE 64Gb/die
UART freq : 0
SATA Status Coalescing : 0
Compressible data performance tuning option : 0 (no tuning for compr. data)
Serial Output Control : 0 (Default)
Write Speed Limit : 0 (Off)
Led Settings
Activity LED Polarity : 0 (Normal)
Fault LED Polarity : 0 (Normal)
LED Blink Rate : 0 (250ms)
Power Managment Settings
Power Management Version : 2 (B01)
Active State Power Mode : 0 (Default)
DIPM Behavior in Active State : 0 (Default)
HIPM Behavior in Active State : 2 (HIPM NAK)
Auto Idle Enable : 0 (Default)
Idle State Power Mode : 0 (Default)
DIPM Behavior in Idle State : 0 (Default)
HIPM Behavior in Idle State : 2 (HIPM NAK)
Standby State Power Mode : 0 (Default)
DIPM Behavior in Standby State : 0 (Default)
HIPM Behavior in Standby State : 2 (HIPM NAK)
Sleep State Power Mode : 0 (Default)
DIPM Behavior in Sleep State : 0 (Default)
HIPM Behavior in Sleep State : 2 (HIPM NAK)
Auto slumber timer : 0
CMU power down : 0 (Default)
Dual-align BIST Feature : 0 (Default)
Temperature Sensor Settings
Sensor 1:
Device ID : 2 (LM73)
Device Address : 0
Max Temperature Threshold Level 1 Entry Point (MT1) : 0n (Default - 65C)
Max Temperature Threshold Level 2 Entry Point (MT2) : 0n (Default - 70C)
Min Temperature Threshold (LT1) : 0n (Default - 0C)
Max Temperature Threshold Behavior for MT1 (MT1B) : 0 (Default)
Max Temperature Threshold Behavior for MT2 (MT2B) : 0 (Default)
Min Temperature Threshold Behavior (LT1B) : 0 (Default)
Max Temperature Threshold Level 1 Return Point (MTR1): 0 (Default - MT1)
Sensor 2:
Device ID : 255 (Disabled)
Device Address : 0
Max Temperature Threshold Level 1 Entry Point (MT1) : 0
Max Temperature Threshold Level 2 Entry Point (MT2) : 0
Min Temperature Threshold (LT1) : 0
Max Temperature Threshold Behavior for MT1 (MT1B) : 0 (Default)
Max Temperature Threshold Behavior for MT2 (MT2B) : 0 (Default)
Min Temperature Threshold Behavior (LT1B) : 0 (Default)
Max Temperature Threshold Level 1 Return Point (MTR1): 0
Security Erase Options
Security Erase Behavior : 0 (Default)
Enhanced Security Erase Behavior (Military Erase) : 0 (Default)
SATA Command and Firmware Options
Flush Cache Behavior : 0 (Default)
ATA Security Set Enable : 0 (Default)
Spread Spectrum Clocking Enable : 0 (Default)
SATA Link Handling on Reboot : 0 (Default)
ACS2 Support : 0 (Default)
Failed Secure Unlock Delay Enable : 0 (Default(No delay))
Seek Complete in Error Status : 0 (Default)
Read Long with Retry and without Retry : 0 (Default)
Read Sectors without Retry : 0 (Default)
Write DMA without Retry : 0 (Default)
Write Long with Retry and without Retry : 0 (Default)
Max SATA Link Rate : 0 (Default)
Deterministic Trim Setting : 0 (Default)
Controller Drive Strength Rate : 0 (Default)
PHY Setting : 0 (Default)
Controller Slew Rate : 0 (Default)
Put SIG FIS Delay : 0 (Default)
Set Multiple Handling : 0 (Default)
TRIM Timer Abort : 0 (Enable(Default))
Trim Support/Setting Word 169 Bit 0 : 0 (Default(Firmware default setting))
RDD1 Optimization : 0 (Default)
Security Unlock Drive : 0 (Default(Compare Master Password))
Power Throttling Options
Average Power Level 0-100 : 0
Maximum Power Level 0-100 : 0
Power Throttling Upon Unsafe Shutdown : 0 (Default)
Dynamic Read Scrub
Read Scrub Enabled : 0 (Default (Enabled))
Dynamic Read Scrub End Range1 : 0
Dynamic Read Scrub Rate Range1 : 0
Dynamic Read Scrub End Range2 : 0
Dynamic Read Scrub Rate Range2 : 0
Dynamic Read Scrub End Range3 : 0
Dynamic Read Scrub Rate Range3 : 0
Dynamic Read Scrub End Range4 : 0
Dynamic Read Scrub Rate Range4 : 0
Low Level Format Settings
Number of entries in Max LBA Setting : 1
Sub-Sector Size [0] : 512
Pattern Size [0] : 2
Sub-Sector and Patterns per sector [0] : 0
Max LBA Count [0] : 125045424
Host Protected Area
Host Protected Access : 1 (Reset only if SSP is disabled)
End of Life Behavior
Enable End of Life : 0 (Default (EOL Enabled))
EOL Threshold 1 Type : 0 (Default (SSD Life Left))
EOL Threshold 1 Percentage : 0
EOL Threshold 1 Behavior : 0 (Default (Light Write Throttling))
EOL Threshold 2 Type : 0 (Default (SSD Life Left))
EOL Threshold 1 Percentage : 0
EOL Threshold 1 Behavior : 0 (Default (Heavy Write Throttling))
CDU Smart settings: default
Fab Defect list entry : 7
Idx Bus CE Die Plane Block Lane3210 Defects
0 0 0 0 0 45 BBBB 4
1 0 0 0 1 45 BBBB 4
2 0 1 0 0 45 BBBB 4
3 0 1 0 1 45 BBBB 4
4 0 1 0 0 128 ___B 1
5 0 1 0 0 557 __B_ 1
6 0 1 0 0 561 __B_ 1
Fab Defects : 19
User Defect list entry: 0
Panic Dumps : 0
Panic Dumps list:
Idx Accurev SyncCode UnlockLevel Size DataSize EPA Log Ok CRC Ok
0 -1 0xffffffff 0xffffffff -1 -1 0x00040002 0x0000 0x0000
1 -1 0xffffffff 0xffffffff -1 -1 0x00040082 0x0000 0x0000
2 -1 0xffffffff 0xffffffff -1 -1 0x00050002 0x0000 0x0000
3 -1 0xffffffff 0xffffffff -1 -1 0x00050082 0x0000 0x0000
MST settings not exist.
MST result not exits.
[/more]
лог FAIL:
[more]ser@localhost ~]$ su
[root@localhost liveuser]# /media/DATA/ADATA/SF_Genesis_v1.7/SF_Genesis -PROCESS_SSD 4:0:0:0 /media/DATA/NEWFL/FW_PPRO_5_8_2_Release.906190.release--0/FW_PPRO_5_8_2_Release.906190.release.0.mfp /media/DATA/NEWFL/FW_PPRO_5_8_2_Release.906190.release--0/Configuration_Files/28199.0.driveconfig 1D4720126848 www_123 log=/media/DATA/ADATA/log
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
SandForce Genesis Utility v1.7.0.01020130612-fc14-32bit
SF_Core Library: v1.7.1.20130612-fc14-32bit
Copyright 2010-2012, LSI Corporation, All Rights Reserved Worldwide.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[Thu 11/28/2019 07:15:32] - SF_Genesis has been invoked with the following parameters:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
argv[1]: -PROCESS_SSD
argv[2]: 4:0:0:0
argv[3]: /media/DATA/NEWFL/FW_PPRO_5_8_2_Release.906190.release--0/FW_PPRO_5_8_2_Release.906190.release.0.mfp
argv[4]: /media/DATA/NEWFL/FW_PPRO_5_8_2_Release.906190.release--0/Configuration_Files/28199.0.driveconfig
argv[5]: 1D4720126848
argv[6]: www_123
argv[7]: log=/media/DATA/ADATA/log
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[Thu 11/28/2019 07:15:32] - Instructing the operating system to purge any existing cached data for device: '4:0:0:0'
[Thu 11/28/2019 07:15:37] - Issuing a discovery command for device: '4:0:0:0'
[Thu 11/28/2019 07:15:42] - Discovery command completed...
[Thu 11/28/2019 07:15:42] - Waiting 5 seconds for the system to settle...
[Thu 11/28/2019 07:15:47] - Device designation string '4:0:0:0' is mapped to node '/dev/sg3'
[Thu 11/28/2019 07:15:47] - Proceeding to process SSD device with the following parameters:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
DeviceName = /dev/sg3
MFP Package Filename = /media/DATA/NEWFL/FW_PPRO_5_8_2_Release.906190.release--0/FW_PPRO_5_8_2_Release.906190.release.0.mfp
Configuration File = /media/DATA/NEWFL/FW_PPRO_5_8_2_Release.906190.release--0/Configuration_Files/28199.0.driveconfig
Serial No. = 1D4720126848
World Wide Name = www_123
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[Thu 11/28/2019 07:15:47] - Successfully received the IDENTIFY data from the drive...
[Thu 11/28/2019 07:15:47] - Validating Manufacturing Firmware Package: /media/DATA/NEWFL/FW_PPRO_5_8_2_Release.906190.release--0/FW_PPRO_5_8_2_Release.906190.release.0.mfp
[Thu 11/28/2019 07:16:36] - Successfully opened the package: /media/DATA/NEWFL/FW_PPRO_5_8_2_Release.906190.release--0/FW_PPRO_5_8_2_Release.906190.release.0.mfp
[Thu 11/28/2019 07:16:36] - file /media/DATA/NEWFL/FW_PPRO_5_8_2_Release.906190.release--0/Configuration_Files/28199.0.driveconfig Loaded successfully
[Thu 11/28/2019 07:16:36] - Warning: Unable to query diagnostics information to perform power management settings check
[Thu 11/28/2019 07:16:36] - B01 Power Management configuration request detected
[Thu 11/28/2019 07:16:36] - Successfully extracted *.DriveConfig file: /media/DATA/NEWFL/FW_PPRO_5_8_2_Release.906190.release--0/Configuration_Files/28199.0.driveconfig
[Thu 11/28/2019 07:16:36] - Extracted Config_ID: 1 (28199) in DriveConfig file: /media/DATA/NEWFL/FW_PPRO_5_8_2_Release.906190.release--0/Configuration_Files/28199.0.driveconfig
[Thu 11/28/2019 07:16:36] - Extracted SerialOutputControl: 0
[Thu 11/28/2019 07:16:57] - Searching for flashware image for configuration 28199
[Thu 11/28/2019 07:16:57] - Manifest found for configuration 28199
[Thu 11/28/2019 07:16:57] - Flashware image extracted: 28199_fw_cl_mlc_Intel_64Gb_JS29F16B08CCMF3_1Q_2C_1D_S_PP_R01909_s512.vic
[Thu 11/28/2019 07:16:57] - Searching for manufacturing image for configuration 28199
[Thu 11/28/2019 07:16:57] - Manifest found for configuration 28199
[Thu 11/28/2019 07:16:57] - Manufacturing image extracted: 28199_mf_mlc_Intel_64Gb_JS29F16B08CCMF3_1Q_2C_1D_S_PP_R01909_s512.vic
[Thu 11/28/2019 07:16:57] - Proceeding in ROM mode, download feature 3...
[Thu 11/28/2019 07:16:57] - Successfully downloaded MFB to the drive...
[Thu 11/28/2019 07:16:57] - Waiting (5 sec) for the drive to settle...
[Thu 11/28/2019 07:17:02] - Successfully received the IDENTIFY data from the drive...
[Thu 11/28/2019 07:17:02] - Firmware revision reported to be: '582ABBM0'. This indicates MFB download was successful.
[Thu 11/28/2019 07:17:02] - Successfully enabled SMART capabilities...
[Thu 11/28/2019 07:17:04] - Successfully issued a diagnostic unlock...
[Thu 11/28/2019 07:17:05] - Performing the flash test of block 0 (0x0000)...
[Thu 11/28/2019 07:17:08] - Flash Test Results:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-----------------------------------------------------------------------------
Flash Test Parameters:
-----------------------------------------------------------------------------
Block Count: 0
Page Count: 1
Bus Count: 1
Chip Enabled Count: 2
Die Count: 1
Lane Count: 4
Plane Count: 2
-----------------------------------------------------------------------------
Results Notes:
-----------------------
N1 - At least one page tested and passed with no bit errors.
N2 - No test data available. Test may have aborted, or failed during the testing.
N3 - At least one page tested and had errors less than or equal to half the range of ECC correction power.
N4 - At least one erased page tested had bit error rate greater than half the correction power.
N5 - Walking zeros test failed.
N6 - Walking ones test failed.
N7 - Block contained factory bad block markings and testing was skipped.
N8 - At least one page tested and had bit error rate greater than the correction power on plane 0.
N9 - Block in plane 0 was marked as a factory bad block.
N10 - At least one page tested and had bit error rate greater than the correction power on plane 1.
N11 - Block in plane 1 was marked as a factory bad block.
-----------------------------------------------------------------------------
+------+------+------+------+--------+--------------------------------------------+---------+
| Bus | CE | Die | Lane | Value | Result Notes | Overall |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 0 | 0 | 0 | 0x0003 | N1,N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 0 | 0 | 1 | 0x0001 | N1 | PASS |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 0 | 0 | 2 | 0x0001 | N1 | PASS |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 0 | 0 | 3 | 0x0001 | N1 | PASS |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 1 | 0 | 0 | 0x0001 | N1 | PASS |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 1 | 0 | 1 | 0x0023 | N1,N3,N5 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 1 | 0 | 2 | 0x0001 | N1 | PASS |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 1 | 0 | 3 | 0x0001 | N1 | PASS |
+------+------+------+------+--------+--------------------------------------------+---------+
-----------------------------------------------------------------------------
Total Number of test results: 8
Number of failures: 0
Number of Passed with warnings: 2
No. Passed without warnings: 6
-----------------------------------------------------------------------------
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[Thu 11/28/2019 07:17:08] - Performing the FORMAT Command with the following parameters:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
MemoryWearCycleCapability = 0
CurrentPE_CycleCount = 0
LifeInSeconds = 0
LogicalCapacity = 125045424
SectorSize = 512
SectorAlignmentOffset = 0
ExpectedMemoryID = 34953 (0x8889)
ExpectedNumDies = 0
SerialOutputControl = 0
Time[8] = 0x0000000000000000
MiscFlag_Erase_R_Block = 0
MiscFlag_PanicHandlingEnabled = 0
MiscFlag_PanicOnSATA_Error = 0
MiscFlag_WriteThrottlingTestMode = 0
MiscFlag_DisableUserBandECCX = 1
L_PageSize = 0
E_PageSize = 0
ErrorCorrectionPower = 0
ConfigDeviceReadDisturbCount = 0
ConfigDeviceReadDisturbCountLow = 0
ExtraOptions_0_1 = 0
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[Thu 11/28/2019 07:17:19] - FATAL_ERROR: Could not perform the FORMAT() operation on the drive... (0x0000C048:SF_SCT (C048h): Root Creation Failed (MFB format))
[Thu 11/28/2019 07:17:19] - End of Genesis manufacturing log.
[Thu 11/28/2019 07:17:19] - Exiting...
[Thu 11/28/2019 07:17:19] - Overall Result for Device: /dev/sg3 ****** FAIL ******
[root@localhost liveuser]# /media/DATA/ADATA/SF_Genesis_v1.7/SF_Genesis -PROCESS_SSD 4:0:0:0 /media/DATA/NEWFL/FW_PPRO_5_8_2_Release.906190.release--0/FW_PPRO_5_8_2_Release.906190.release.0.mfp /media/DATA/NEWFL/FW_PPRO_5_8_2_Release.906190.release--0/Configuration_Files/28199.0.driveconfig 1D4720126848 www_123 log=/media/DATA/ADATA/log
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
SandForce Genesis Utility v1.7.0.01020130612-fc14-32bit
SF_Core Library: v1.7.1.20130612-fc14-32bit
Copyright 2010-2012, LSI Corporation, All Rights Reserved Worldwide.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[Thu 11/28/2019 07:17:53] - SF_Genesis has been invoked with the following parameters:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
argv[1]: -PROCESS_SSD
argv[2]: 4:0:0:0
argv[3]: /media/DATA/NEWFL/FW_PPRO_5_8_2_Release.906190.release--0/FW_PPRO_5_8_2_Release.906190.release.0.mfp
argv[4]: /media/DATA/NEWFL/FW_PPRO_5_8_2_Release.906190.release--0/Configuration_Files/28199.0.driveconfig
argv[5]: 1D4720126848
argv[6]: www_123
argv[7]: log=/media/DATA/ADATA/log
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[Thu 11/28/2019 07:17:53] - Instructing the operating system to purge any existing cached data for device: '4:0:0:0'
[Thu 11/28/2019 07:17:58] - Issuing a discovery command for device: '4:0:0:0'
[Thu 11/28/2019 07:18:03] - Discovery command completed...
[Thu 11/28/2019 07:18:03] - Waiting 5 seconds for the system to settle...
[Thu 11/28/2019 07:18:08] - Device designation string '4:0:0:0' is mapped to node '/dev/sg3'
[Thu 11/28/2019 07:18:08] - Proceeding to process SSD device with the following parameters:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
DeviceName = /dev/sg3
MFP Package Filename = /media/DATA/NEWFL/FW_PPRO_5_8_2_Release.906190.release--0/FW_PPRO_5_8_2_Release.906190.release.0.mfp
Configuration File = /media/DATA/NEWFL/FW_PPRO_5_8_2_Release.906190.release--0/Configuration_Files/28199.0.driveconfig
Serial No. = 1D4720126848
World Wide Name = www_123
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[Thu 11/28/2019 07:18:08] - Successfully received the IDENTIFY data from the drive...
[Thu 11/28/2019 07:18:08] - FATAL_ERROR: This drive is already running MFB, please perform a force-download to enter in to the ROM mode first. Genesis can not process drive in the current state... (0x10090020:SF_GENESIS_ALREADY_RUNNING_MFB_ERROR)
[Thu 11/28/2019 07:18:08] - End of Genesis manufacturing log.
[Thu 11/28/2019 07:18:08] - Exiting...
[Thu 11/28/2019 07:18:08] - Overall Result for Device: /dev/sg3 ****** FAIL ******
[root@localhost liveuser]#
[/more]
лог PASS:
[more]ser@localhost ~]$ su
[root@localhost liveuser]# /media/DATA/ADATA/SF_Genesis_v1.7/SF_Genesis -PROCESS_SSD 4:0:0:0 /media/DATA/NEWFL/FW_PPRO_5_8_2_Release.906190.release--0/FW_PPRO_5_8_2_Release.906190.release.0.mfp /media/DATA/NEWFL/FW_PPRO_5_8_2_Release.906190.release--0/Configuration_Files/28199.0.driveconfig 1D4720126848 www_123 log=/media/DATA/ADATA/log
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
SandForce Genesis Utility v1.7.0.01020130612-fc14-32bit
SF_Core Library: v1.7.1.20130612-fc14-32bit
Copyright 2010-2012, LSI Corporation, All Rights Reserved Worldwide.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[Thu 11/28/2019 19:16:48] - SF_Genesis has been invoked with the following parameters:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
argv[1]: -PROCESS_SSD
argv[2]: 4:0:0:0
argv[3]: /media/DATA/NEWFL/FW_PPRO_5_8_2_Release.906190.release--0/FW_PPRO_5_8_2_Release.906190.release.0.mfp
argv[4]: /media/DATA/NEWFL/FW_PPRO_5_8_2_Release.906190.release--0/Configuration_Files/28199.0.driveconfig
argv[5]: 1D4720126848
argv[6]: www_123
argv[7]: log=/media/DATA/ADATA/log
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[Thu 11/28/2019 19:16:48] - Instructing the operating system to purge any existing cached data for device: '4:0:0:0'
[Thu 11/28/2019 19:16:53] - Issuing a discovery command for device: '4:0:0:0'
[Thu 11/28/2019 19:16:58] - Discovery command completed...
[Thu 11/28/2019 19:16:58] - Waiting 5 seconds for the system to settle...
[Thu 11/28/2019 19:17:03] - Device designation string '4:0:0:0' is mapped to node '/dev/sg3'
[Thu 11/28/2019 19:17:03] - Proceeding to process SSD device with the following parameters:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
DeviceName = /dev/sg3
MFP Package Filename = /media/DATA/NEWFL/FW_PPRO_5_8_2_Release.906190.release--0/FW_PPRO_5_8_2_Release.906190.release.0.mfp
Configuration File = /media/DATA/NEWFL/FW_PPRO_5_8_2_Release.906190.release--0/Configuration_Files/28199.0.driveconfig
Serial No. = 1D4720126848
World Wide Name = www_123
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[Thu 11/28/2019 19:17:03] - Successfully received the IDENTIFY data from the drive...
[Thu 11/28/2019 19:17:03] - Validating Manufacturing Firmware Package: /media/DATA/NEWFL/FW_PPRO_5_8_2_Release.906190.release--0/FW_PPRO_5_8_2_Release.906190.release.0.mfp
[Thu 11/28/2019 19:17:52] - Successfully opened the package: /media/DATA/NEWFL/FW_PPRO_5_8_2_Release.906190.release--0/FW_PPRO_5_8_2_Release.906190.release.0.mfp
[Thu 11/28/2019 19:17:52] - file /media/DATA/NEWFL/FW_PPRO_5_8_2_Release.906190.release--0/Configuration_Files/28199.0.driveconfig Loaded successfully
[Thu 11/28/2019 19:17:52] - Warning: Unable to query diagnostics information to perform power management settings check
[Thu 11/28/2019 19:17:52] - B01 Power Management configuration request detected
[Thu 11/28/2019 19:17:52] - Successfully extracted *.DriveConfig file: /media/DATA/NEWFL/FW_PPRO_5_8_2_Release.906190.release--0/Configuration_Files/28199.0.driveconfig
[Thu 11/28/2019 19:17:52] - Extracted Config_ID: 1 (28199) in DriveConfig file: /media/DATA/NEWFL/FW_PPRO_5_8_2_Release.906190.release--0/Configuration_Files/28199.0.driveconfig
[Thu 11/28/2019 19:17:52] - Extracted SerialOutputControl: 0
[Thu 11/28/2019 19:18:13] - Searching for flashware image for configuration 28199
[Thu 11/28/2019 19:18:13] - Manifest found for configuration 28199
[Thu 11/28/2019 19:18:13] - Flashware image extracted: 28199_fw_cl_mlc_Intel_64Gb_JS29F16B08CCMF3_1Q_2C_1D_S_PP_R01909_s512.vic
[Thu 11/28/2019 19:18:13] - Searching for manufacturing image for configuration 28199
[Thu 11/28/2019 19:18:13] - Manifest found for configuration 28199
[Thu 11/28/2019 19:18:13] - Manufacturing image extracted: 28199_mf_mlc_Intel_64Gb_JS29F16B08CCMF3_1Q_2C_1D_S_PP_R01909_s512.vic
[Thu 11/28/2019 19:18:13] - Proceeding in ROM mode, download feature 3...
[Thu 11/28/2019 19:18:13] - Successfully downloaded MFB to the drive...
[Thu 11/28/2019 19:18:13] - Waiting (5 sec) for the drive to settle...
[Thu 11/28/2019 19:18:18] - Successfully received the IDENTIFY data from the drive...
[Thu 11/28/2019 19:18:18] - Firmware revision reported to be: '582ABBM0'. This indicates MFB download was successful.
[Thu 11/28/2019 19:18:18] - Successfully enabled SMART capabilities...
[Thu 11/28/2019 19:18:20] - Successfully issued a diagnostic unlock...
[Thu 11/28/2019 19:18:21] - Performing the FORMAT Command with the following parameters:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
MemoryWearCycleCapability = 0
CurrentPE_CycleCount = 0
LifeInSeconds = 0
LogicalCapacity = 125045424
SectorSize = 512
SectorAlignmentOffset = 0
ExpectedMemoryID = 34953 (0x8889)
ExpectedNumDies = 0
SerialOutputControl = 0
Time[8] = 0x0000000000000000
MiscFlag_Erase_R_Block = 0
MiscFlag_PanicHandlingEnabled = 0
MiscFlag_PanicOnSATA_Error = 0
MiscFlag_WriteThrottlingTestMode = 0
MiscFlag_DisableUserBandECCX = 1
L_PageSize = 0
E_PageSize = 0
ErrorCorrectionPower = 0
ConfigDeviceReadDisturbCount = 0
ConfigDeviceReadDisturbCountLow = 0
ExtraOptions_0_1 = 0
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[Thu 11/28/2019 19:18:29] - FORMAT command completed...
[Thu 11/28/2019 19:18:29] - Waiting (2 sec) for the drive to settle...
[Thu 11/28/2019 19:18:31] - Setting up the stamp information through CDU command...
[Thu 11/28/2019 19:18:34] - Waiting (2 sec) for the drive to settle...
[Thu 11/28/2019 19:18:36] - Downloading the flashware to the drive... feature 3
[Thu 11/28/2019 19:18:38] - Successfully downloaded flashware to the drive...
[Thu 11/28/2019 19:18:38] - Waiting (15 sec) for the drive to settle...
[Thu 11/28/2019 19:18:53] - Successfully received the IDENTIFY data from the drive...
[Thu 11/28/2019 19:18:53] - Firmware revision reported to be: '4.0.0 '
[Thu 11/28/2019 19:18:53] - Enabling SMART support...
[Thu 11/28/2019 19:18:53] - Issuing a diagnostic unlock to the drive...
[Thu 11/28/2019 19:18:55] - Setting up Max LBA settings...
[Thu 11/28/2019 19:18:59] - Change of sector size is not required, sector size is already set to 512
[Thu 11/28/2019 19:19:00] - Setting the serial number of the drive to: 1D4720126848
[Thu 11/28/2019 19:19:02] - Setting the World Wide Name (WWN) of the drive to: www_123
[Thu 11/28/2019 19:19:05] - Processing completed for device: 1D4720126848
[Thu 11/28/2019 19:19:05] - Begin collecting the device post-process log/information
[Thu 11/28/2019 19:19:05] - Creating the Log Bundle...
[Thu 11/28/2019 19:19:05] - Plain text identify log created
[Thu 11/28/2019 19:19:06] - Plain text diagnostics identify log created
[Thu 11/28/2019 19:19:07] - Plain text diagnostics information log created
[Thu 11/28/2019 19:19:08] - Plain text format information log created
[Thu 11/28/2019 19:19:08] - Plain text SMART log created
[Thu 11/28/2019 19:19:10] - Plain text manufacturing defect list log created
[Thu 11/28/2019 19:19:11] - Plain text grown defect list log created
[Thu 11/28/2019 19:19:12] - Plain text panic directory listing log created
[Thu 11/28/2019 19:19:12] - Completed collecting all plain text log files.
[Thu 11/28/2019 19:19:12] - End of logs and information collection
[Thu 11/28/2019 19:19:13] - Applying the remaining ConfigUniqueDrive settings...
[Thu 11/28/2019 19:19:14] - Setting Customer ID with value : 0
[Thu 11/28/2019 19:19:14] - Setting Diagnostic Unlock Key with value supplied
[Thu 11/28/2019 19:19:14] - Setting Max LBA Count for 4096 Plus DIFF Sectors with value : 0
[Thu 11/28/2019 19:19:14] - Setting Max LBA Count for 4096 Sectors with value : 0
[Thu 11/28/2019 19:19:14] - Setting Max LBA Count for 512B Plus DIFF Sectors with value : 0
[Thu 11/28/2019 19:19:14] - Setting Max LBA Count for 512B Sectors with value : 0
[Thu 11/28/2019 19:19:14] - Setting Max LBA Count for 520B Sectors with value : 0
[Thu 11/28/2019 19:19:14] - Setting Max LBA Count for 524B Sectors with value : 0
[Thu 11/28/2019 19:19:14] - Setting Max LBA Count for 528B Sectors with value : 0
[Thu 11/28/2019 19:19:14] - Total of 1 valid MaxLBA settings were setup to be written to the drive.
[Thu 11/28/2019 19:19:16] - Successfully applied the remaining ConfigUniqueDrive settings...
[Thu 11/28/2019 19:19:16] - Issuing an IdleImmediate command to the drive...
[Thu 11/28/2019 19:19:16] - Not an Enterprise drive,so, continuing without setting master password..
[Thu 11/28/2019 19:19:16] - End of Genesis manufacturing log.
[Thu 11/28/2019 19:19:16] - Exiting...
[Thu 11/28/2019 19:19:16] - Overall Result for Device: /dev/sg3 ****** PASS ******
[root@localhost liveuser]# ^C
[root@localhost liveuser]#
[/more]
Мне кажется, что ошибки при прошивке возникают при включенной галке Test Flash. Тогда Genesis видимо прогонят память на бэды и если ему что-то не нравится - дальше не шьет.
Т.е. если есть такая запись в логе:
[more][Thu 11/28/2019 07:17:08] - Flash Test Results:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-----------------------------------------------------------------------------
Flash Test Parameters:
-----------------------------------------------------------------------------
Block Count: 0
Page Count: 1
Bus Count: 1
Chip Enabled Count: 2
Die Count: 1
Lane Count: 4
Plane Count: 2
-----------------------------------------------------------------------------
Results Notes:
-----------------------
N1 - At least one page tested and passed with no bit errors.
N2 - No test data available. Test may have aborted, or failed during the testing.
N3 - At least one page tested and had errors less than or equal to half the range of ECC correction power.
N4 - At least one erased page tested had bit error rate greater than half the correction power.
N5 - Walking zeros test failed.
N6 - Walking ones test failed.
N7 - Block contained factory bad block markings and testing was skipped.
N8 - At least one page tested and had bit error rate greater than the correction power on plane 0.
N9 - Block in plane 0 was marked as a factory bad block.
N10 - At least one page tested and had bit error rate greater than the correction power on plane 1.
N11 - Block in plane 1 was marked as a factory bad block.
-----------------------------------------------------------------------------
+------+------+------+------+--------+--------------------------------------------+---------+
| Bus | CE | Die | Lane | Value | Result Notes | Overall |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 0 | 0 | 0 | 0x0003 | N1,N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 0 | 0 | 1 | 0x0001 | N1 | PASS |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 0 | 0 | 2 | 0x0001 | N1 | PASS |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 0 | 0 | 3 | 0x0001 | N1 | PASS |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 1 | 0 | 0 | 0x0001 | N1 | PASS |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 1 | 0 | 1 | 0x0023 | N1,N3,N5 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 1 | 0 | 2 | 0x0001 | N1 | PASS |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 1 | 0 | 3 | 0x0001 | N1 | PASS |
+------+------+------+------+--------+--------------------------------------------+---------+[/more]
- скорее всего не прошьется - все что кроме N1 будет приводить к ошибке.
Чтобы программа sp_info могла прочитать данные - Device Unlock Code надо ставить 16 нулей, а не как пишут везде 1,2,3,4,5,6,7,8,9,0,1,2,3,4,5,6. Это можно ручками прямо в конфиге прописать.
Ну и после прошивки имею следющие отличия от второго диска:
Signature : 158-0-28199 - на родном, Signature : 196-0-28199 - на прошитом. Думаю это vendor ID - ни на что не влияет, программа ADATA диск видит.
На непрошитом диске:
FW : [CV5ABBF0 ]
FW string : [B:FW_PPRO_DALECREST:FW_PPRO_C_V_5_Release-545010
На прошитом:
FW : [582ABBF0 ]
FW string : [B:FW_PPRO_5_6_1_20140326_836378:FW_PPRO_5_8_2_Release-906190
- думаю прошивка все-же не такая как была, более новая, но не уверен.
Однако по тестам скорости - она стала выше раза в 1,5 и на чтение и на запись.
Еще в непрошитом:
Max PE Cycles : need fw.360+/520+
Cur PE Cycles : need fw.360+/520+
А в прошитом:
Max PE Cycles : 3000
Cur PE Cycles : 0
что это такое - не знаю, но время жизни показывает как-то по разному.
Всем огромное спасибо за собранный материал и помощь!
Жалко что сам ресурс не очень юзабельный... крайне тяжело работать с таким форумом... но может это дело привычки. [/more] [/more]